3form Hardware Catalog: Point Support

20mm (3/4") Cap w/ 20mm (3/4") threaded rod, for Varia only
3-15-0020-K (kit contents)

20mm(3/4") Cap w/ 20mm(3/4") M8 threaded rod, for Varia only. Order min. thread length 3/8" (10mm) longer than material gauge.

25mm(1in) Cap w/ 20mm(3/4in) threaded rod
3-15-0025-K (kit contents)

25mm(1in) Cap w/ 20mm(3/4in) M8 threaded rod and (2) panel pressure fit washers. Order min. thread length 3/8in (10mm) longer than material gauge.

25mm(1") Cap w/ 25mm(1") threaded rod
3-15-0028-K (kit contents)

25mm(1") Cap w/ 25mm(1") M8 threaded rod and (2) Press Fit washers. Order min. thread length 3/8" (10mm) longer than material gauge.

25mm(1") Cap w/ 32mm(1 1/4") threaded rod
3-15-0029-K (kit contents)

25mm(1") Cap w/ 32mm(1 1/4") M8 threaded rod and (2) press fit washers.. Order min. thread length 3/8" (10mm) longer than material gauge.

Align Curve kit for 1" gauge material
3-15-0070-K (kit contents)

Large 2-sided panel connector hardware with an M8 screw for 1" gauge material. Panel fabrication required with this hardware. Also comes with 4 1/16" gauge self-adhesive shims for gauge variance.

Align Smooth Large kit for 1/2" gauge material (panel fabrication required)
3-15-0071-K (kit contents)

Large 2-sided panel connector hardware with 2 M5 screws for 1/2" gauge material. Panel fabrication required with this hardware. Also comes with 4 1/16" gauge self-adhesive shims for gauge variance.

Align Curve kit for 1/2" gauge material
3-15-0074-K (kit contents)

Large 2-sided panel connector hardware with an M8 screw for 1/2" gauge material. Panel fabrication required with this hardware. Also comes with 4 1/16" gauge self-adhesive shims for gauge variance.

Align Curve kit for 3/4" gauge material
3-15-0075-K (kit contents)

Large 2-sided panel connector hardware with an M8 screw for 3/4" gauge material. Panel fabrication required with this hardware. Also comes with 4 1/16" gauge self-adhesive shims for gauge variance.

Align Curve kit for 2" gauge material
3-15-0076-K (kit contents)

Large 2-sided panel connector hardware with an M8 screw for 2" gauge material. Panel fabrication required with this hardware. Also comes with 4 1/16" gauge self-adhesive shims for gauge variance.

Align Smooth Large kit for 3/4" gauge material
3-15-0078-K (kit contents)

Large 2-sided panel connector hardware with 2 M5 screws for 3/4" gauge material. Panel fabrication required with this hardware. Also comes with 4 1/16" gauge self-adhesive shims for gauge variance.

Align Smooth Large kit for 2" gauge material
3-15-0080-K (kit contents)

Large 2-sided panel connector hardware with 2 M5 screws for 2" gauge material. Panel fabrication required with this hardware. Also comes with 4 1/16" gauge self-adhesive shims for gauge variance.

Align Smooth kit for 1/4" gauge material
3-15-0081-K (kit contents)

2-sided panel connector hardware with 2 M3 screws for 1/4" gauge material

Align Smooth kit for 3/8" gauge material
3-15-0082-K (kit contents)

2-sided panel connector hardware with 2 M3 screws for 3/8" gauge material

Pressed Glass Support Adapter for Thinner Gauges
3-15-0608-K (kit contents)

For 3form Pressed glass products gauges 5/16" - 1/2" only, includes adapter and 3form threaded cap

Pressed Glass Support Adapter for Thicker Gauges
3-15-0609-K (kit contents)

For 3form Pressed glass products gauges 9/16" - 3/4" only, includes adapter and 3form threaded cap

Offset Align Kit for 3/8in Gauge Material
3-15-0621-K (kit contents)

Aligns 2 panels, providng stability to prevent deflection by tying to a wall behind. Comes with anchors to allow placement of 4 inches away from the wall. Intended to bear no weight but provide panel to panel alignment and resistance against applied force

Offset Align Kit for 1/2in Gauge Material
3-15-0622-K (kit contents)

Offset Align Kit for 5/8 - 3/4in Gauge Material
3-15-0623-K (kit contents)

Double-Sided Offset Align Kit for 1/2in Gauge Material & 4in cavity
3-15-0624-K (kit contents)

Aligns (2) 1/2in panels in the same plane while also attaching to 2 panels behind through a 4" cavity, providng stability to prevent deflection. Intended to bear no weight but provide panel to panel alignment and resistance against applied force

Premium inserts cannot be used with this product.

20mm(3/4") x 25mm(1") Barrel
3-15-0720

M8 Threads

20mm(3/4") x 50mm(2") Barrel
3-15-0721

M8 Threads

20mm(3/4") x 75mm(3") Barrel
3-15-0722

M8 Threads

25mm(1") x 25mm(1") Barrel
3-15-0725

M8 Threads

25mm(1") x 50mm(2") Barrel
3-15-0726

M8 Threads

25mm(1") x 75mm(3") Barrel
3-15-0727

M8 Threads

25mm(1") x 100mm(4") Barrel
3-15-0728

M8 Threads

25mm(1") x 150mm(6") Barrel
3-15-0729

M8 Threads

4" 4-hole Mounting Plate
3-15-0733-K (kit contents)

Includes screws. Requires 1/4"-20 toggle bolts if mounting to drywall

M8 Toggle Bolt Anchor
3-15-0734

Hollow Wall Anchor with M8 threads. 50 or 60mm threaded rod and flange recommended. Do not exceed 70 lbs in tensile and shear forces for drywall applications.

4-Point Spider
3-15-0766

Anodized Aluminum w/M8 Threads. Includes M8 x 14mm countersunk fastener and locating pin. Requires T-Nut when used with Versa.

2-Point Spider
3-15-0767

Anodized Aluminum w/M8 Threads. Includes M8 x 14mm countersunk fastener and locating pin. Requires T-Nut when used with Versa.

1-Point Spider
3-15-0768

Anodized Aluminum w/M8 Threads. Includes M8 x 14mm countersunk fastener and locating pin. Requires T-Nut when used with Versa.

2-Point Spider Straight
3-15-0781

Anodized Aluminum w/M8 Threads. Includes M8 x 14mm countersunk fastener and locating pin. Requires T-Nut when used with Versa.

Spanner Wrench (ST)
3-15-0782

Spanner Wrench for Standard Caps

M8 Threaded Insert
3-15-0791

M8 Threaded insert. (Threaded Insert for Wood) Pre-drill .40" hole

Align Smooth Large kit for 1" gauge material
3-15-0861-K (kit contents)

Large 2-sided panel connector hardware with 2 M5 screws for 1" gauge material. Panel fabrication required with this hardware. Also comes with 4 1/16" gauge self-adhesive shims for gauge variance.

Offset Align Kit for 1in Gauge Material
3-15-0871-K (kit contents)

Offset Align Kit for 2in Gauge Material
3-15-0872-K (kit contents)

Tubing
3-15-1003

5/16" ID x 9/16" OD Tubing for using standoffs with glass. Follow guidelines in the Pressed Glass specification sheet through Tech Specs and Downloads on the 3form website. 5/8" Pre-drilled hole recommended for installation. Specify length in inches.

Tubing Cutter
3-15-1004

Cutter for tubing

SDS Hammerdrill 10mm concrete bit
3-15-1013

10mm hammer drill masonry bit, SDS shank for M8 concrete anchors, also use for 3-15-1610

4 Bolt Panel Connector w/hole
3-15-1511 (kit contents)

2" x 2" SS with brushed finish. Removable roller pins. For use with 1/4" or 1/2" panels, for Varia / 100 Percent only

20mm(3/4") x 12mm(1/2") Spacer
3-15-1543

1/2" Spacer with thru hole

20mm(3/4") x 6mm(1/4") Spacer
3-15-1544

1/4" Spacer with thru hole

25mm(1") x 12mm(1/2") Spacer
3-15-1552

1/2" Spacer with thru hole

25mm(1") x 6mm(1/4") Spacer
3-15-1553

1/4" Spacer with thru hole

Concrete Flush Anchor HKD-S M8x30
3-15-1610

Concrete flush anchors for regular use. Not ICC rated. Requires 3-15-1612 setting tool, drill 10mm hole (3-15-1013). See anchoring manual for more details.

Low Profile Cap Key
3-15-1704

2-prong key for tightening low profile caps. Recommend 1 key for every 5 caps.

Patent Pending

Standard thinner gauge 2-piece cap head kit
3-15-1716-K (kit contents)

Standard 2-piece cap head kit with all necessary washers and bushings for 3/16" gauge material and below; no rod included.

Standard thicker gauge 2-piece cap head kit
3-15-1719-K (kit contents)

Standard 2-piece cap head kit with all necessary washers and bushings for 1/4" gauge material and above; no rod included. Will work with all 3form material types. Order threaded rod separately.

M8 Threaded Rod, 20mm
3-15-1753

For 2-piece cap, for use with 1/16" - 1/8" material

M8 Threaded Rod, 35mm
3-15-1755

For 2-piece cap, for use with 1/2" gauge material

Countersunk M8 screw, 30mm
3-15-1756

For Countersunk assemblies for use with 1/2" gauge material

Countersunk M8 screw, 45mm
3-15-1757

For Countersunk assemblies for use with 1" gauge material

Countersunk M8 screw, 35mm
3-15-1758

For Countersunk assemblies for use with 3/4" gauge material

Variable Angle Barrel 1" dia.
3-15-1792

1" Dia. Barrel Variable Angle, full 180 degree rotation capability that can then be locked into place; Accepts M8 Threaded rods and caps.

M8 Wood anchor, 50mm
3-15-3001

38mm lag, 12mm machine thread

M8 Wood anchor, 60mm
3-15-3002

38mm lag, 22mm machine thread

M8 Concrete Anchor
3-15-3011A

60mm length, Rod not included

M8 Threaded Rod, 30mm
3-15-3032

For 2-piece caps with 3/8" gauge material and concrete anchors, SS

M8 Threaded Rod, 50mm
3-15-3032A

For 2-piece caps with 1" gauge material and For 60mm concrete anchors, SS. If mounting material to 1" barrel with flange, use 40mm rod; if using with 1" barrel and no flange, use 35mm rod.

M8 Threaded Rod, 40mm
3-15-3033

For 2-piece caps with 3/4" gauge material and concrete anchors, SS

M8 Threaded Rod, 60mm
3-15-3033A

For 60mm concrete anchors, SS

M8 x 50mm Flange
3-15-3051

SS, Internal threads

M8 Nut
3-15-3061

M8 Threaded Nut

50mm Flange with Through hole
3-15-3064

50mm Flange with through hole for use with Hidden Point system when mounting adapter directly to wall.

Clear Silicon Washer for use with Point Supports with Glass or Chroma
3-15-3333

3/4" diameter, 1/8" thick compressible washer for use with glass and Chroma. Follow guidelines in the Pressed Glass or Chroma specification sheet through Tech Specs and Downloads on the 3form website. No glass or Chroma should contact metal directly.

M6 Universal Anchoring Kit
3-15-6000-K (kit contents)

M6 size anchoring kit for all available substrate types. Includes a toggle bolt, wood insert, concrete anchor, and threaded rod. Specify one kit per connection.

M8 Universal Anchoring Kit for Point Support
3-15-8000-K (kit contents)

M8 size anchoring kit for all available substrate types, including a toggle bolt, wood insert, concrete anchor, Point Support flange, and 25 mm and 50 mm threaded rod. Specify one kit per connection with Point Support.

Clear Tubing for point support
3-15-8894

Clear Tubing for point support

Premium inserts cannot be used with this product.

Right Angle Internal Attachment Clip
3-60-2265

Right angle attachment clip used to create an invisible internal thread behind panels

Premium inserts cannot be used with this product.

Thick compressible washer
3-15-0151

Thick compressible silicon washer used with Point Support attachments on a textured panel

Premium inserts cannot be used with this product.

Select your Country / Language

Solutions

3form Hardware Catalog: Point Support